LifePO4 6.4V 1800mAh built-in battery electronic led converter for LED panel or LED downlight

LifePO4 6.4V 1800mAh built-in battery electronic led converter for LED panel or LED downlight

1. Description

1) Constant Power Output: Experience consistent and reliable power supply for your LED lighting systems, ensuring uninterrupted illumination.
2) Input/Output Relay Switching: Seamlessly switch between normal and emergency modes during power outages for continuous lighting operation
3) Multiple Protection Functions: Benefit from battery overcharge and over-discharge protection, along with output short circuit protection for enhanced safety.
4) Built-in Battery, Easy Replacement: Enjoy the convenience of a built-in battery with easy replacement, ensuring hassle-free maintenance.

2. Parameters

Charge Part	KE006	KE006-02M180HB	KE006-03M180HB
		KE006-02A180HB	KE006-03A180HB
	Rated input voltage	220-240Vac 50Hz /60Hz
	Rated input current	0.05A Max. @230Vac
	Input inrush current	10A(Twidth=100uS 50% Ipeak )@230Vac(Cold start at full load )
	Power factor	≥0.5@230Vac
	Input power	<4W
	Battery charging current	200mA Max
	Battery charging time	24 hours Max
Emergency Part	Operating mode	Emergency mode
	Load type	LED
	Emergency power	2W	2.5W
	Emergency time	3 hours
	Load output current	100-30mA	150-45mA
	Load output voltage	20-60VDC
Battery	LifePO4 (The battery capacity meets the emergency time at 25℃)	6.4V 1800mAh
	Battery warranty	Warranty 3 years, Design Life 5 years.
Exception Driver Requirements	Surge current	8A
	Input current	3 A Max.
	Output current	3 A Max.
LED Indication (Manual test)	Charging	Greenlight
	Fault	Green light off
Emergency Function Test	Manual test	KE006-02M180HB / KE006-02M180HB
	Autotest	KE006-02A180HB / KE006-02A180HB
Auto Testing	Fault/test / Status	Reason	Charge Indicator Status
	Battery fully charged and operational	Standard daily use
			solid green
	Battery Charging	Initial Charge/Battery Top Up
			solid green
	Auto Test 3 Hours (every 12 months)	Periodic self-test
			Flashing Green 3 sec on 1 sec off
	Auto Test 5 Min (every 30 days)	Periodic self-test
			Flashing Green 3 sec on 3 sec off
	Duration test fault	Failed the 3-hour annual test
			Flashing Red 0.5 sec on 0.5 sec off
	LED fault	Not plugged in or damaged/faulty
			Flashing Red 2 sec on – 2 sec off
	Battery Disconnected/Faulty	Not plugged in or damaged/faulty
			solid red
Abnormal protection	over-charge/deep discharge protection	Yes
	Output over-voltage protection	Yes
	Output overload protection	Yes
	Output short circuit protection	Yes
Operating Environment	Operating temperature/humidity	0℃…+50℃; humidity:20%-75%(without condensation)
	Storage temperature/humidity	-5℃-35℃
	Case Max. Temp(Tc)	75℃
Safety & EMC	Withstand voltage	3000Vac 5mA 60S (Input “L N” – output “SEC+ SEC-)
	Safety standard	EN61347-1, EN61347-2-7
	EMC standard	EN55015, EN61000-3-2, EN61000-3-3
	Battery standard	UN38.3
	Environmental protection requirements	Compliant to RoHS
	Certification	CE
Others	In/output(terminal/wiring)specification	Press terminal, wire diameter:0.75-1.5mm2
	IP rating	IP20
	Type of protection	Class 2
	Installation type	Built-in installation
	Installation dimension	211*42.5*25mm
	Packaging requirement	White box+Instruction manual+clapboard+outer carton(K=A)
	Weight	200g;
	Lifespan	5 Year @Ta ( Battery not included )
Notes: All parameters are tested on the input voltage 230Vac, environment temperature 25℃ unless otherwise specified.

3. Dimension (Unit:mm)

4. Wiring Diagram

OR

5 . Manual Test & Operation Instructions

1). Connect the wire according to the wiring diagram.

2). L, N power on, Switch on S1. then the load lamp turns on, The emergency driver indicator light turns green, emergency power supply normally charging. Turn off Switch S1, and the load lamp turns off.

3). Emergency Simulation: Switch on, the load lamp turns on, press the switch(TEST SWITCH), then switch to emergency mode, the indicator light of the emergency driver will be extinguished. Release the switch(TEST SWITCH), then the lamp is powered by the LED driver, the indicator light will turn on.

7. Battery Application Notice

1)The battery should be recharged and discharged semiannually in normal use conditions.

2)Do not connect to the circuit when the battery is not used to prevent over-discharge of the battery due to self-consumption of the circuit board.

3)Please keep the battery from the heat source when installing and using it, and only be allowed to use it in a certain working temperature range.

4)The battery should be stored in a cool and dry environment.

5)After a long time of storage, the battery is cycled every 12 months as required.